Standard
UPDATE AVAILABLE
AS/NZS ISO 7176.25:2014
[Superseded]Wheelchairs, Part 25: Batteries and chargers for powered wheelchairs
Adopts ISO 7176.25:2013, which specifies requirements and test methods for batteries and battery chargers intended for use with electrically powered wheelchairs.
Published: 17/02/2014
Pages: 17
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
Preface
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Apparatus
4.1
4.2
4.3
4.4
4.5
5 Battery chargers
5.1 Electrical safety
5.1.1 General
5.1.2 Requirements
5.1.2.1
5.1.2.2
5.1.2.3
5.1.2.4
5.1.3 Test methods
5.1.3.1 General
5.1.3.2 Exposure to vibration
5.1.3.2.1 On-board battery chargers
5.1.3.2.2 Carry-on battery chargers
5.2 Performance-related safety
5.2.1 General
5.2.2 Charging connector
5.2.2.1 General
5.2.2.2 Requirements
5.2.2.3 Test methods
5.2.3 Reverse polarity connection
5.2.3.1 General
5.2.3.2 Requirements
5.2.3.3 Test method
5.2.4 Battery discharge
5.2.4.1 General
5.2.4.2 Requirement
5.2.4.3 Test method
5.2.5 Battery charger options
5.2.5.1 General
5.2.5.2 Requirements
5.2.5.3 Test method
5.2.6 Charging a faulty battery set
5.2.6.1 General
5.2.6.2 Requirements
5.2.6.3 Test method
5.2.7 Thermal runaway
5.3 Charging capability
5.3.1 General
5.3.2 Requirements
5.3.2.1 Charging current
5.3.2.2 Charging voltage
5.3.3 Preparation for test
5.3.4 Test methods
5.3.4.1 Charging current set-up
5.3.4.2 R.M.S. output current
5.3.4.3 Mean output current
5.3.4.4 Thermal stability
5.3.4.5 Charging voltage
5.4 Electromagnetic compatibility
5.4.1 General
5.4.2 Requirements
5.4.3 Test methods
5.5 Indicators
5.5.1 General
5.5.2 Requirements
5.5.3 Test method
6 Batteries
6.1 Requirements
6.1.1 Endurance and charge retention
6.1.2 Marking
6.2 Test method
7 Test report
7.1 Test reports for battery chargers
7.2 Test reports for batteries
8 User manual
8.1 User manual for battery chargers
8.2 User manual for batteries
9 Disclosure
Annex A
A.1 General
A.2 Recommendations
Bibliography
Cited references in this standard
IATA
Special Provision A67
SAE J1495
Test Procedure for Battery Flame Retardant Venting Systems
[Current]
Connectors for electrical and electronic equipment - Product requirements - Part 2-101: Circular connectors - Detail specification for M12 connectors with screw-locking
[Current]
Corrigendum 1 - Amendment 2 - Degrees of protection provided by enclosures (IP Code)
[Current]
Household and similar electrical appliances - Safety - Part 2-40: Particular requirements for electrical heat pumps, air-conditioners and dehumidifiers
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$113.54 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$113.54 AUD
IMPORTANT