Standard
Track updates
AS/NZS 4013:2014
[Pending Revision]Domestic solid fuel burning appliances - Method for determination of flue gas emission
This Standard specifies a test method for determining the particulate emission factor from batch-fed domestic solid fuel burning appliances and the associated particulate emission acceptance criteria.
Published: 08/08/2014
Pages: 22
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
Preface
1 Scope and general
1.1 Scope
1.2 Application
1.2.1 General
1.2.2 Included appliances
1.2.3 Excluded appliances
1.3 Referenced documents
1.4 Definitions
1.5 Principle
2 Apparatus and reagent
2.1 General
2.2 Ambient temperature measurement system
2.3 Ambient air pressure measurement system
2.4 Weight determination system
2.5 Sampling train
2.6 Draught gauge
2.7 Desiccators
2.8 Acetone
2.9 Dishes
2.10 Carbon dioxide analyzer (optional)
3 Configuration of test equipment
3.1 General
3.2 Dilution tunnel
3.2.1 Hood
3.2.2 Connectors
3.2.3 Bends
3.2.4 Sampling section
3.2.5 Extraction fan
3.2.6 Component assembly
3.2.7 Pitot tube location
3.3 Sampling train
3.3.1 General
3.3.2 Probe
3.3.3 Filter coupling
3.3.4 Temperature probes
3.3.5 Dryer coupling
3.3.6 Exhaust pump
3.3.7 Joint seals
4 Calibrations
4.1 General
4.2 Dry gas meter
4.3 Dilution tunnel
4.4 Weighing instruments
4.5 Temperature measurement
4.6 Differential pressure manometer and draught gauge
4.7 Carbon dioxide analyzer
5 Test fuel
5.1 General
5.2 Test fuel requirements for Australia
6 Test procedure
6.1 General
6.2 Dilution hood and tunnel
6.3 Dilution tunnel
6.3.1 General
6.3.2 Flue pipe draught
6.4 Test preparation
6.4.1 Appliance preparation
6.4.2 Sample collection system
6.5 Test fuel load
6.5.1 Preparation
6.5.2 Fuel-loading geometry
6.6 Burn cycles
6.7 Sampling train operation
6.8 Sample treatment
6.9 Sample measurement
6.10 Calculations
6.10.1 Sample weight
6.10.2 Sample flow volume
6.10.3 Dilution tunnel flow volume
6.10.4 Volume ratio
6.10.5 Particulate emission weight
6.10.6 Particulate emission factor
6.10.7 Burn-rate emission factors
6.10.8 Appliance particulate emission factor
7 Maximum allowable appliance particulate emission factor
7.1 For Australia
7.1.1 Appliances without catalytic combustors
7.1.2 Appliances with catalytic combustors
7.2 For New Zealand
7.3 Valid tests
8 Testing documentation and test reports
8.1 General
8.2 Documentation
8.3 Test report
8.4 Retention of records
8.5 Published results
9 Variation from tested appliance
9.1 General
9.2 Retesting exemption
10 Marking
Appendix A
A1 Scope
A2 Principle
A3 Apparatus
A4 Procedure
A5 Report
Appendix B
B1 Scope
B2 Principle
B3 Procedure
B4 Report
Appendix C
C1 Scope
C2 Principle
C3 Apparatus
C4 Calibration procedure
C5 Calibration before each use
Cited references in this standard
AS/NZS 4014
Domestic solid fuel burning appliances—Test fuels (series)
[Current]
Domestic solid fuel burning appliance — Method for determination of power output and efficiency
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$119.17 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$119.17 AUD
IMPORTANT