Standard
UPDATE AVAILABLE
Track updates
AS/NZS 1562.3:1996
[Available Superseded]Design and installation of sheet roof and wall cladding, Part 3: Plastic
Specifies the procedures for the design and installation of plastic roof and wall cladding materials.
Published: 05/03/1996
Pages: 17
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
PREFACE
1 SCOPE AND GENERAL
1.1 SCOPE
1.2 REFERENCED DOCUMENTS
1.3 REFERENCED STANDARDS
2 GENERAL REQUIREMENTS
2.1 SCOPE OF SECTION
2.2 MATERIAL
2.3 TRANSPORT, HANDLING AND STORAGE
2.4 SAFETY PRECAUTIONS
2.4.1 General
2.4.2 Fire precautions
2.4.3 Safety mesh
2.4.3.1 General
2.4.3.2 Provision of safety mesh
2.4.4 Walking and standing on roofs
2.4.4.1 General
2.4.4.2 Walkways
2.4.4.3 Notices
3 DESIGN OF PLASTIC ROOF AND WALL CLADDING
3.1 SCOPE OF SECTION
3.2 AGGRESSIVE ENVIRONMENTS
3.3 LOADINGS
3.3.1 Wind forces
3.3.2 Loadings during construction
3.3.3 Bracing
3.4 SUPPORTING STRUCTURE
3.5 RAFTERS, BATTENS AND PURLINS
3.5.1 Alignment
3.5.2 Width and depth
3.6 STUDS AND NOGGINGS (DWANGS)
3.6.1 Alignment
3.6.2 Width and depth
3.7 FASTENERS
4 INSTALLATION
4.1 INSTALLATION OF ROOF AND WALL CLADDING SHEETS
4.1.1 Scope
4.1.2 General provisions
4.1.2.1 Inspection
4.1.2.2 Cutting of sheets
4.1.2.3 Supports at hips and valleys
4.1.2.4 End laps
4.1.2.5 Side laps at inserts
4.1.2.6 Projections through sheeting
4.1.2.7 Fastening procedure
4.1.2.8 Fastener types
4.1.2.9 Fastener holes
4.1.2.10 Washers
4.1.2.11 Sealing at flashings on roofs
4.1.2.12 Unsupported overhang
4.1.3 Installation of safety mesh
4.2 INSTALLATION OF uPVC WALL CLADDING BOARDS
4.2.1 Scope
4.2.2 Application
4.2.3 General provisions
4.2.3.1 Inspection
4.2.3.2 Cutting of boards
4.2.3.3 End laps
4.2.3.4 Butt joints
4.2.3.5 Projections through boards
4.2.4 Handling and storage
4.2.5 Installation precautions
4.2.5.1 Fire
4.2.5.2 Termites
4.2.5.3 Wall vents
4.2.6 Installation
4.2.6.1 Preparation
4.2.6.2 Spacing
4.2.6.3 Thermal expansion
4.2.6.4 Fasteners
4.2.6.5 Waterproofing
4.2.6.6 Alignment
5 TESTING
5.1 APPLICABILITY OF TESTS
5.2 RESISTANCE TO WIND FORCES
5.2.1 General
5.2.2 Resistance to wind pressures for non-cyclone regions
5.2.2.1 General
5.2.2.2 Strength test
5.2.3 Resistance to wind pressures for cyclone regions
5.2.3.1 General
5.2.3.2 Strength test
5.3 RESISTANCE TO IMPACT (SANDBAG) FOR ROOFING SHEET MATERIALS
5.3.1 General
5.3.2 Assessment
5.4 RESISTANCE TO IMPACT (SANDBAG) FOR WALL CLADDING BOARDS
APPENDIX A
APPENDIX B
B1 GENERAL
B2 LOADING
B3 DEEMED TO COMPLY
B4 POSITION AND FIXING
B5 CORROSIVE ATMOSPHERE
APPENDIX C
C1 SCOPE
C2 PRINCIPLE
C3 APPARATUS
C3.1 Test frame
C3.2 Test loads
C3.2.1 Dynamic
C3.2.2 Static
C4 TEST SPECIMEN
C5 PROCEDURE
C6 REPORT
Cited references in this standard
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$83.52 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$83.52 AUD
IMPORTANT