Standard
UPDATE AVAILABLE
Track updates
AS/NZS 1254:2010
[Current]PVC-U pipes and fittings for stormwater and surface water applications
Specifies requirements for PVC pipes and fittings for underground disposal of storm or surface water. The Standard includes requirements for both plain and structured wall pipes and fittings.
Published: 06/04/2010
Pages: 30
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
Preface
1 Scope and general
1.1 Scope
1.2 Referenced documents
1.3 Definitions
1.4 Notation
1.5 Classification
2 General requirements
2.1 General
2.2 Composition
2.3 Colour
2.4 Freedom from defects
2.4.1 General
2.4.2 Spigot ends
2.5 Requirements for elastomeric seals
2.6 Solvent cements
2.7 Packaging, storage and transportation
2.8 Additional requirements for best environmental practice PVC pipes and fittings
3 Performance requirements
3.1 General
3.2 Tests on pipes
3.2.1 Pipe impact characteristics at 20°C
3.2.2 Bond strength (for hollow profile wall pipes only)
3.2.3 Pipe stiffness (for all pipes DN90 and greater)
3.2.4 Ring flexibility test (for structured wall pipes only)
3.3 Tests on moulded and fabricated fittings
3.3.1 Hydrostatic pressure test
3.3.2 High temperature stress relief test
3.3.3 Stiffness (for structured and hollow profile wall fittings only)
3.4 Tests on elastomeric seal joints
3.4.1 General
3.4.2 Hydrostatic pressure test
4 Pipes
4.1 General
4.2 Diameter and wall thickness
4.3 Length
4.4 Pipe spigot ends
4.5 Sockets formed on pipe ends
4.6 Marking
4.7 Witness mark
5 Moulded fittings
5.1 General
5.2 Dimensions of moulded fittings
5.2.1 General
5.2.2 Spigot ends
5.2.3 Sockets on moulded fittings
5.3 Wall thickness
5.4 Minimum free bore
5.5 Test openings
5.5.1 General
5.5.2 Sealing rings
5.5.3 Threaded caps
5.6 Marking
6 Fabricated fittings
6.1 General
6.2 Materials
6.3 Compliance
6.4 Minimum free bore
6.5 Marking
7 Elastomeric seal joints
7.1 General
7.2 Materials
7.3 Design
7.4 Effective sealing length
Appendix A
A1 Scope
A2 Relevance
A3 Batch
A3.1 Acceptable quality level (AQL)
A3.2 Batch
A3.2.1 Material or compound batch
A3.2.2 Pipes or fittings batch
A3.3 Batch release test
A3.4 Inspection level
A3.5 Lot
A3.6 New formulation
A3.7 Process verification test (PVT)
A3.8 Sample
A3.9 Sampling plan
A3.10 Type test (TT)
A4 [Text deleted.]
A5 Minimum sampling and testing frequency plan
A5.1 General
A5.2 Testing
A5.3 Retesting
A5.4 Rejection after test
A6 New formulation
[Appendix deleted.]
[Bibliography deleted.]
Amendment control sheet
AS/NZS 1254:2010
Amendment No. 1 (2011)
Revised text
Amendment No. 2 (2013)
Correction
Amendment No. 3 (2018)
Revised text
Amendment No. 4 (2024)
Revised text
Cited references in this standard
[Current]
Methods of test for plastics pipes and fittings, Method 1: Method for determining the dimensions of pipes and fittings
[Current]
Elastomeric seals — Material requirements for pipe joint seals used in water and drainage applications, Part 1: Vulcanized rubber
[Current]
Elastomeric seals — Material requirements for pipe joint seals used in water and drainage applications, Part 2: Thermoplastic elastomers
[Current]
Sampling procedures for inspection by attributes, Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
Content history
[Current]
[Current]
[Current]
[Current]
[Superseded]
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$119.17 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$119.17 AUD
IMPORTANT