Standard
UPDATE AVAILABLE
Track updates
AS/NZS 1200:2000
[Available Superseded]Pressure equipment
Sets out basic requirements and good practice for the design, materials, manufacture, examination,testing, installation, conformity assessment, commissioning, operation, inspection, maintenance, repair, alteration and disposal of pressure equipment (boilers, pressure vessels and pressure piping) but excluding gas cylinders. Includes detailed requirements for various pressure equipment by direct reference to a range of Australian, New Zealand and other Standards.
Published: 23/06/2000
Pages: 34
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
PREFACE
1 SCOPE AND GENERAL
1.1 SCOPE
1.2 OBJECTIVE
1.3 APPLICATION
1.4 DEFINITIONS
1.5 REFERENCED DOCUMENTS
1.6 SUPPLEMENT, AMENDMENT, ENQUIRY CASE AND RULING
1.6.1 Enquiry
1.6.2 Supplement, Amendment, Enquiry Case and Ruling
1.7 NEW DESIGNS, MATERIALS AND MANUFACTURING METHODS
1.8 ROUNDING OF NUMERICAL VALUES
1.9 CONVERSION OF UNITS
1.10 TOLERANCES
1.11 CONCESSIONS
1.12 IMPLEMENTATION
1.13 REFERENCE TO STANDARDS
2 BASIC REQUIREMENTS AND COMPLIANCE STANDARDS
2.1 BASIC REQUIREMENTS AND RECOMMENDATION
2.2 COMPLIANCE STANDARDS
2.3 MIXING STANDARDS
APPENDIX A
A1 PRESSURE EQUIPMENT COVERED
A2 EXAMPLES
A3 EQUIPMENT OR PLANT UNDER PRESSURE NOT SPECIFICALLY COVERED
APPENDIX B
B1 INTRODUCTION
B2 ENQUIRY
B3 APPLICATION FOR ENQUIRY
APPENDIX C
C1 POLICY FOR MATERIALS
C1.1 General
C1.2 Permitted material Standards
C1.3 Alternative national Standards
C2 NEW MATERIAL
C2.1 Amendment or Supplement
C2.2 Mechanical properties
C2.3 Weldability
C2.4 Physical changes
APPENDIX D
D1 GENERAL
D2 SPECIFIC REQUIREMENTS
D2.1 Design verification
D2.2 Fabrication inspection
D2.3 Inspection openings
APPENDIX E
E1 GENERAL
E2 DEFINITIONS
APPENDIX F
F1 SCOPE
F2 COMPARISON OF AUSTRALIAN AND OVERSEAS PRESSURE EQUIPMENT STANDARDS
APPENDIX G
APPENDIX H
APPENDIX I
I1 SEISMIC LOADINGS
I2 ADDITIONAL REQUIREMENTS FOR SEISMIC LOADINGS
I3 WIND AND SNOW LOADINGS
APPENDIX J
J1 GENERAL
J2 BASIC RECOMMENDATIONS
J2.1 Design and manufacture
J2.2 Use
J3 DESIGN
J3.1 General
J3.2 Design for adequate strength and deflection control
J3.2.1 General
J3.2.2 Basis
J3.2.3 Calculation method
J3.2.4 Experimental design
J3.3 Design for safe handling and operation
J3.4 Means of examination
J3.5 Means of isolation, draining and venting
J3.6 Corrosion or other chemical attack
J3.7 Wear
J3.8 Provisions for filling and discharge
J3.9 Protection against exceeding allowable limits
J3.10 Safety accessories
J3.10.1 General
J3.10.2 Pressure limiting devices
J3.10.3 Temperature limiting devices
J3.11 External fire
J4 MANUFACTURE
J4.1 Manufacturing procedures
J4.1.1 General
J4.1.2 Preparation of the component parts
J4.1.3 Joining
J4.1.4 Non-destructive tests
J4.1.5 Heat treatment
J4.1.6 Traceability
J4.1.7 Repair
J4.2 Final assessment
J4.2.1 General
J4.2.2 Final inspection
J4.2.3 Proof test
J4.3 Marking and labelling
J4.4 Operating instructions
J5 MATERIALS
J5.1 General
J5.2 Materials for pressurized parts
J5.3 Documentation
J5.4 Compliance
J6 SAFETY REQUIREMENTS FOR SPECIAL APPLICATIONS
J6.1 Fired or otherwise heated pressure equipment with a risk of overheating
J6.2 Additional safety recommendations for piping
J7 USE
J7.1 General
J7.2 Equipment operations
J7.3 Safety management system
Cited references in this standard
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$141.91 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$141.91 AUD
IMPORTANT