Standard
UPDATE AVAILABLE
Track updates
AS 5102.1:2019
[Current]Performance of household electrical appliances — Swimming pool pump-units, Part 1: Measurement of energy consumption and performance
This Standard specifies requirements for the determination of energy consumption of swimming pool pump units operating on single-phase electricity.
Published: 07/11/2019
Pages: 37
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
Preface
Introduction
1 Scope and general
1.1 Scope
1.2 Normative references
1.3 Terms and definitions
1.4 Notation
2 Pump unit classification and input power range
2.1 Scope
2.2 Classification criteria
2.3 Input power range
3 Performance rating procedure
3.1 Scope
3.2 Operating conditions — Rating points
3.2.1 General
3.2.2 Single-speed pump units
3.2.3 Two-speed pump units
3.2.4 Multi-speed and variable speed pump units
3.3 Performance factors
3.3.1 Performance factors for single-speed pump units
3.3.2 Performance factors for two-, multi- and variable speed pump units
3.4 Pump unit performance curves
4 Test facility
4.1 Scope
4.2 Test system
4.2.1 General
4.2.2 Pipe and fittings specifications
4.2.3 Pressure tappings
4.2.4 Characteristics of water used in test
4.3 Temperature conditions
4.3.1 Water temperature
4.3.2 Air temperature
4.4 Electrical supply
4.5 Test system flow control
5 Operating point and measurements
5.1 Scope
5.2 Curve D operating point
5.3 Test facility data acquisition
5.3.1 Test facility data acquisition and analysis
5.3.2 Pressure and flow rate sensors
5.4 Measurements required
5.5 Measurement of flow rate
5.6 Pressure measurement
5.7 Evaluation of pump unit total head
5.8 Measurement of pump unit input power and power factor
5.9 Measurement of sound power
6 Calibration, data sampling and measurement
6.1 Scope
6.2 Calibration of test equipment
6.3 Data recording
6.3.1 Sampling rate
6.3.2 Sampling period
6.4 Steady conditions
6.5 Unsteady conditions
7 Test methods
7.1 Scope
7.2 General
7.3 Preparation
7.3.1 Pump unit installation
7.3.2 Pump unit operation
7.4 Measurement of pump unit performance
7.4.1 Single-speed pump units
7.4.2 Two-speed pump units
7.4.3 Multi- and variable speed pump units
7.5 Procedure
7.5.1 General
7.5.2 Measurements when pump unit operating stably on Curve D
7.5.3 Measurement of pump unit performance curves
7.6 Calculations
7.7 Test report
Appendix A
A.1 General
A.2 Report forms
Appendix B
Appendix C
C.1 Determination of measurement error (ε)
C.1.1 Specification of results and errors
C.1.2 Systematic uncertainty (εS)
C.1.3 Random uncertainty (εR)
C.2 Uncertainty in measuring set point (εΔH)
C.3 Sensitivity of weighted energy factor to set point errors
C.3.1 Weighted energy factor error
C.3.2 Variation of WEF due to set point error for single-speed pump
C.3.3 Variation of WEF due to set point errors for multi-speed pump
C.3.4 Set point error limit and set point bias
C.4 Uncertainty in weighted energy factor (εWEF)
Bibliography
Amendment control sheet
AS 5102.1:2019
Amendment No. 1 (2022)
Correction amendment
Amendment No. 2 (2023)
Revised text amendment
Cited references in this standard
[Current]
Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Precision methods for reverberation test rooms
ISO 3743.1
Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for small movable sources in reverberant fields — Part 1: Comparison method for a hard-walled test room
Content history
[Current]
[Current]
[Available Superseded]
DR AS 5102.1:2019
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$141.91 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$141.91 AUD
IMPORTANT