Standard
Track updates
AS 2317.1:2018
[Current]Lifting points, Part 1: Collared eyebolts and collared eyenuts — Grade 4
This Standard specifies requirements for Grade 4 forged collared eyebolts and collared eyenuts used for lifting.
Published: 31/10/2018
Pages: 37
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
Preface
Introduction
1 Scope and general
1.1 Scope and application
1.1.1 Scope
1.1.2 Application
1.2 Normative references
1.3 Terms and definitions
2 Design and manufacture
2.1 Material
2.1.1 Quality of material
2.1.2 Type of steel production
2.1.3 Deoxidation
2.1.4 Material requirements
2.1.5 Traceability
2.1.6 Temperature requirements
2.1.7 Ductility
2.2 Heat treatment
2.2.1 General
2.2.2 Hardness requirement
2.3 Design and manufacturing requirements
2.3.1 Design requirements
2.3.2 Forging
2.3.3 Machining
2.3.4 Screw thread
2.3.5 Surface finish
2.4 Mechanical properties
2.4.1 General
2.4.2 Axial strength
2.4.3 Transverse strength
2.5 Marking
2.5.1 General
2.5.2 Size
2.5.3 Information
3 Testing
3.1 Type testing of mechanical properties
3.1.1 General
3.1.2 Test for deformation
3.1.3 Type test
3.1.4 Testing for transverse strength
3.1.5 Test samples
3.2 Manufacturing tests
3.2.1 Manufacturing examination
3.2.2 Manufacturing proof test
3.2.3 Non-destructive test
3.3 Proof loading
3.4 Requirements
3.5 Test certificates
4 Care and use of eyebolts and eyenuts
4.1 Small eyebolts and eyenuts
4.2 Matching of threads
4.3 Anchorage
4.4 Threaded attachment
4.4.1 Collar interface
4.4.2 Washers
4.4.3 Untapped (through) holes
4.4.4 Hole tolerance
4.4.5 Tapped holes
4.4.6 Threaded studs
4.4.7 Soft or non-metallic materials
4.5 Tightening of eyebolts and eyenuts
4.6 Alignment of eye
4.7 Continuous slings
4.8 Loading when not aligned
4.8.1 General
4.8.2 Transverse loading
4.8.3 Lateral loading
4.9 Use with multiple eyebolts or eyenuts
4.10 Use with single eyebolt or eyenut
4.11 Service eyebolts and eyenuts
4.12 Lifting capacity while used with slings
4.13 Inspection
4.13.1 General
4.13.2 Cleaning
4.13.3 Before use
4.13.4 Periodic
4.13.5 Discard criteria
4.14 Temperature effects
Appendix A
A.1 General
A.2 Competency standards and procedures
A.3 Visual acuity
Appendix B
Appendix C
Appendix D
Appendix E
Appendix F
Appendix G
G.1 Calibration of test machine
G.2 Pre-condition
G.3 Attachment and force application
Appendix H
H.1 General
H.2 Manufacturing test regime and acceptance criteria when a quality management system is in place and operating
H.3 Manufacturing test regime and acceptance criteria when a quality management system is not in place or not operating
H.4 Product verification and sampling plans
H.4.1 General
H.4.2 Acceptance sampling procedure for proof and mechanical properties testing
H.4.2.1 Sampling plan
H.4.2.2 Static tensile test
H.4.3 Risk-based product verification
Bibliography
Cited references in this standard
[Current]
General requirements for the competence of testing and calibration laboratories
[Current]
Fasteners - Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes
[Current]
Non-destructive testing — Magnetic particle testing of ferromagnetic products, components and structures
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$141.91 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$141.91 AUD
IMPORTANT