Standard
Track updates
AS 1891.5:2020
[Current]Personal equipment for work at height, Part 5: Manufacturing requirements for lanyard assemblies and pole straps
Specifies requirements for the materials, design, manufacture, testing and labelling of lanyard assemblies and pole straps for work at height.
Published: 28/08/2020
Pages: 32
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
Preface
Introduction
1 Scope and general
1.1 Scope
1.2 Exclusions
1.3 Normative references
1.4 Terms and definitions
1.5 Schedule of testing
1.6 Deemed to satisfy
2 Components
2.1 General
2.2 Webbing and thread
2.2.1 Design and construction
2.2.2 Performance requirements
2.3 Ropes and chains
2.4 Hardware
2.4.1 Finish
2.4.2 Corrosion, protection, coatings and testing
2.4.3 Connectors
3 Lanyard assemblies and pole straps
3.1 General
3.2 Common requirements
3.2.1 General
3.2.2 Mass range testing
3.3 Design and construction
3.3.1 Lanyard assembly
3.3.2 Pole strap
3.4 Static and dynamic testing
3.4.1 Minimum pull-out force
3.4.2 Adjuster creep test
3.4.3 Dynamic test — Lanyard assembly
3.4.4 Dynamic test — Pole strap
3.4.5 Static strength test — Lanyard assembly
3.4.6 Static test — Pole strap
4 Instructions and labelling
4.1 Instructions for use
4.2 Labelling requirements
4.2.1 Lanyard assemblies and pole straps
4.2.2 Connectors
4.2.3 Readability
Appendix A
A.1 Scope
A.2 Principle
A.3 Apparatus
A.3.1 Daylight exposure
A.3.2 Artificial light exposure
A.3.3 Breaking strength test
A.4 Test specimens
A.5 Procedure
A.6 Report
Appendix B
B.1 Scope
B.2 Principle
B.3 Apparatus
B.4 Test specimens
B.5 Procedure
B.6 Report
Appendix C
C.1 Scope
C.2 Principle
C.3 Apparatus
C.4 Test specimens
C.5 Procedure
C.6 Report
Appendix D
D.1 Scope
D.2 Principle
D.3 Apparatus
D.4 Test specimens
D.5 Procedure
D.5.1 Test No. 1
D.5.2 Test No. 2
D.5.3 Test No. 3
D.6 Report
Appendix E
E.1 Scope
E.2 Principle
E.3 Apparatus
E.4 Procedure
E.5 Report
Appendix F
F.1 Scope
F.2 Principle
F.3 Apparatus
F.4 Test specimen
F.5 Procedure
F.5.1 Separate lanyard or personal energy absorber
F.5.2 Lanyard assembly with integral harness
F.5.3 Twin-tail lanyard
F.5.3.1 General
F.5.3.2 Test No. 1 — Both tails together
F.5.3.3 Test No. 2 — Each tail separately
F.5.3.4 Test No. 3 — Integrity test for simulated incorrectly stowed unused tail
F.6 Report
Appendix G
Bibliography
Cited references in this standard
EN 362
Personal protective equipment against falls from a height — Connectors
[Current]
Corrosion tests in artificial atmospheres - Salt spray tests - AMENDMENT 1: Footnote of Warning
[Current]
Personal equipment for work at height, Part 1: Manufacturing requirements for full body combination and lower body harnesses
Content history
[Available Superseded]
[Superseded]
[Superseded]
DR AS 1891.5:2020
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$141.91 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$141.91 AUD
IMPORTANT