Standard
Track updates
AS 1562.3-2006
[Current]Design and installation of sheet roof and wall cladding, Part 3: Plastic
Specifies procedures for the design and installation of plastic roof and wall cladding materials for walls and roofs.
Published: 30/06/2006
Pages: 16
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
Preface
1 Scope and general
1.1 Scope
1.2 Referenced documents
2 General requirements
2.1 Scope of section
2.2 Material
2.3 Transport, handling and storage
2.4 Safety precautions
2.4.1 General
2.4.2 Fire precautions
2.4.3 Safety mesh
2.4.3.1 General
2.4.3.2 Provision of safety mesh
2.4.4 Walking and standing on roofs
2.4.4.1 General
2.4.4.2 Walkways
2.4.4.3 Notices
3 Design of plastic roof and wall cladding
3.1 Scope of section
3.2 Aggressive environments
3.3 Loadings
3.3.1 Wind forces
3.3.2 Loadings during construction
3.3.3 Bracing
3.4 Supporting structure
3.5 Rafters, battens and purlins
3.5.1 Alignment
3.5.2 Width and depth
3.5.3 Roof pitch
3.6 Studs and noggings (dwangs)
3.6.1 Alignment
3.6.2 Width and depth
3.7 Fasteners
4 Installation
4.1 Scope of section
4.2 Roof and wall cladding sheets
4.2.1 General provisions
4.2.1.1 Inspection
4.2.1.2 Cutting of sheets
4.2.1.3 Supports at hips and valleys
4.2.1.4 End laps
4.2.1.5 Side laps at inserts
4.2.1.6 Projections through sheeting
4.2.1.7 Fastening procedure
4.2.1.8 Fastener types
4.2.1.9 Fastener holes
4.2.1.10 Washers
4.2.1.11 Sealing at flashings on roofs
4.2.1.12 Unsupported overhang
4.2.2 Installation of safety mesh
4.3 uPVC Wall cladding boards
4.3.1 Application of Clause
4.3.2 General provisions
4.3.2.1 Inspection
4.3.2.2 Cutting of boards
4.3.2.3 End laps
4.3.2.4 Butt joints
4.3.2.5 Projections through boards
4.3.3 Handling and storage
4.3.4 Installation precautions
4.3.4.1 Fire
4.3.4.2 Termites
4.3.4.3 Wall vents
4.3.5 Installation
4.3.5.1 Preparation
4.3.5.2 Spacing
4.3.5.3 Thermal expansion
4.3.5.4 Fasteners
4.3.5.5 Waterproofing
4.3.5.6 Alignment
5 Testing
5.1 Scope of section
5.2 Applicability of tests
5.3 Resistance to wind forces
5.3.1 General
5.3.2 Resistance to wind pressures for non-cyclone regions
5.3.2.1 General
5.3.2.2 Strength test
5.3.3 Resistance to wind pressures for cyclone regions
5.3.3.1 General
5.3.3.2 Strength test
5.4 Resistance to impact (sandbag) for roofing sheet materials
5.4.1 General
5.4.2 Assessment
5.5 Resistance to impact (sandbag) for wall cladding boards
Cited references in this standard
[Current]
Fixed platforms, walkways, stairways and ladders — Design, construction and installation
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$104.71 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$104.71 AUD
IMPORTANT