Standard
Track updates
AS 1418.9:2024
[Current]Cranes, hoists and winches, Part 9: Vehicle hoists
AS 1418.9:2024 establishes uniform minimum safety requirements for vehicle hoists
Published: 13/12/2024
Pages: 54
Table of contents
Cited references
Content history
Table of contents
Header
About this publication
Preface
1 Scope and general
1.1 Scope
1.2 Normative references
1.3 Terms and definitions
1.4 New designs and innovations
1.5 Types of hoists
2 Design
2.1 General
2.1.1 General requirements
2.1.2 Accessibility for maintenance
2.2 Calculations
2.3 Design – structural and mechanical
2.3.1 General
2.3.2 Load combinations
2.3.2.1 Regular loads
2.3.2.2 Dynamic loads
2.3.2.3 Manual forces
2.3.2.4 Effect of attachments and accessories
2.3.2.5 Horizontal forces
2.3.2.6 Wind loads
2.3.2.7 Exceptional loads
2.3.2.7.1 Sudden reactions
2.3.2.7.2 Test loads
2.3.2.7.3 Seismic loads
2.3.2.8 Fatigue analysis and elastic buckling
2.3.2.9 Load distributions
2.3.2.9.1 General
2.3.2.9.2 Wheel supporting vehicle hoist for road vehicles
2.3.2.9.3 Chassis supporting vehicle hoists — using platforms or arms
2.4 Control systems
2.4.1 General
2.4.2 Control devices
2.4.3 Control panels
2.4.4 Location of the panel
2.4.5 Hoist set control system
2.4.6 Wireless systems
2.5 Electrical
2.6 Emergency stop control
2.7 Synchronizing hoist travel
2.8 Travel limiters
2.9 Hoisting limiter
2.10 Adjustable valves including pressure relief valves — pneumatic and hydraulic
2.11 Hydraulic system
2.12 Pneumatic equipment
2.13 Carriage suspension and synchronisation
2.13.1 General
2.13.2 Wire ropes for suspending carriages and equalizing
2.13.3 Chains for carriages and synchronization
2.13.4 Screw suspended carriages
2.14 Attachments and accessories
2.14.1 Accessories
2.14.2 Attachments, components and devices — adjustable supporting arms
2.14.3 Load stool
2.14.3.1 General
2.14.3.2 Height adjustments — mechanisms
2.14.3.3 Height adjustments — inserts
2.14.4 Support pads (pick up pads)
2.15 Anti-creep device and fall arrest system
2.16 Ramps
2.17 Runways
2.18 Wheel stops (wheel supporting hoists)
2.19 Service brakes — self-propelled moveable hoists
2.20 Protection from crushing, shearing and sharp edges
2.21 Handling devices for manually moveable hoists
2.22 Welds
3 Manufacturer’s information
3.1 General
3.2 Manufacturer’s markings
3.3 Information
3.4 Installation and commissioning
3.5 Pre-operational inspection
4 Type test requirements for serial vehicle hoists
4.1 General
4.2 Dynamic testing — endurance
4.3 Dynamic testing — overload
4.4 Static overload load test
4.5 Stability tests
4.6 Testing — fall arrest systems
5 Outsourced components and systems
6 Records of tests
Appendix A
Appendix B
B.1 General
B.2 Standardized structural steel
Appendix C
Appendix D
Appendix E
E.1 Introduction
E.2 General
E.3 Control limitation
E.4 Stop
E.5 Serial data communication
E.6 Use of more than one operator control station
E.7 Battery-powered operator control stations
E.8 Wireless control components
Bibliography
Cited references in this standard
[Current]
Hydraulic fluid power — General rules and safety requirements for systems and their components (ISO 4413:2010, MOD)
[Current]
Pneumatic fluid power — General rules and safety requirements for systems and their components (ISO 4414:2010, MOD)
One-time Purchase
Access via web browser on any device
One-time purchase
Single publication
Offline access via PDF^
$132.00 AUD
Inclusive of GSTFormat *
Web Reader
Licenses *
1 user
Total$132.00 AUD
IMPORTANT